Frigidaire Factory Service ManualFault Code: E64

Frigidaire Dryer Error Code E64: Heating Element Circuit Open / Thermal Limiter Tripped

The electronic control board detects zero current draw across the electric heating element circuit during a designated heat cycle.

Target Appliance

dryer

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Step 1: Physical & Electrical InspectionMultimeter & Visual

Action: Disconnect electrical power, remove rear panel or front lower panel to access heating element chamber.

Bench Test: Disconnect heater power wires and measure resistance across heating element terminals with multimeter.

Expected Standard: Normal resistance is approximately 11.5 to 14.5 ohms at room temperature.

If Failed / Out of Spec:

Resistance reads open circuit (0L). Replace coiled heating element assembly (137392700).

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual

Action: Test continuity across the high-limit thermal safety fuse mounted directly on the heater housing.

Bench Test: Measure resistance across safety fuse spade terminals.

Expected Standard: 0 ohms (closed circuit).

If Failed / Out of Spec:

Fuse is open (blown). Replace high-limit safety thermostat kit (5303281153) and inspect duct for clogs.

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual

Action: Test continuity across thermal limiter mounted on blower housing.

Bench Test: Measure resistance across blower thermal limiter contacts.

Expected Standard: 0 ohms (closed circuit).

If Failed / Out of Spec:

Thermal limiter tripped. Replace thermal limiter (134120900).

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual

Action: Inspect motor centrifugal heater switch contacts.

Bench Test: Test centrifugal switch terminal 1M to 2M with motor at rest vs simulated run position.

Expected Standard: Contacts open when stationary, close when motor achieves running RPM.

If Failed / Out of Spec:

Clean lint from centrifugal switch or replace drive motor (137115900).

If Passed:

Replace electronic control board heater relay (137008000).

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Frigidaire dryer error code E64. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component Name	OEM Part Number	Manufacturer	Status
Electric Heating Element Assembly	`137392700`	Frigidaire	Direct Fit OEM
High-Limit Safety Thermostat Kit	`5303281153`	Frigidaire	Direct Fit OEM
Blower Housing Thermal Limiter	`134120900`	Frigidaire	Direct Fit OEM

Need Local Diagnostic Assistance?

Connect with a Certified Frigidaire Technician in Your Area

If multimeter testing reveals an internal short, locked motor, or fried control board, let an experienced local technician complete the repair with certified OEM replacement parts.

Call for Immediate Technician Dispatch Search Another Code

Frequently Asked Questions: Frigidaire E64

What causes Frigidaire dryer error code E64?

The electronic control board detects zero current draw across the electric heating element circuit during a designated heat cycle.

Can I reset the E64 code by unplugging the dryer?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E64 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Frigidaire E64?

Common OEM replacement components include: Electric Heating Element Assembly (OEM #137392700), High-Limit Safety Thermostat Kit (OEM #5303281153), Blower Housing Thermal Limiter (OEM #134120900).