Bosch Factory Service ManualFault Code: E17

Bosch Washer Error Code E17: Water Fill Time Exceeded / Inlet Supply Restriction

The front-load washing machine did not reach the target water level in the tub within the programmed 6-minute fill timeout window.

Target Appliance

washer

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Step 1: Physical & Electrical InspectionMultimeter & Visual

Action: Verify home cold and hot supply shutoff valves are turned fully on and hoses are not kinked.

Bench Test: Disconnect supply hoses into a 5-gallon bucket and turn taps on to check flow rate.

Expected Standard: Strong continuous flow at 20 to 120 PSI water pressure.

If Failed / Out of Spec:

Clear plumbing supply line restriction or replace kinked stainless hose.

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual

Action: Unscrew water inlet hoses from rear of washer and extract the fine mesh filter screens.

Bench Test: Inspect mesh inlet filters for rust flakes, sediment, or municipal mineral scale.

Expected Standard: Filter screens clean and clear.

If Failed / Out of Spec:

Clean or replace water inlet filter screens (00424981).

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual

Action: Test resistance across cold and hot water inlet solenoid valve coils.

Bench Test: Remove top panel, disconnect solenoid terminals, and measure resistance using multimeter.

Expected Standard: Normal coil resistance is approximately 3.8k to 4.5k ohms (3,800 to 4,500 Ω).

If Failed / Out of Spec:

Open or shorted coil. Replace dual water inlet valve assembly (00622324).

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual

Action: Inspect the electronic analog pressure sensor and translucent air pressure tube.

Bench Test: Check air pressure tube for cracks, pinholes, or water condensation trap clog.

Expected Standard: Air tube intact, firmly seated on tub barb with zero air leaks.

If Failed / Out of Spec:

Replace air pressure tube (00605923) or pressure sensor (00627460).

If Passed:

Replace main motor control board (11018241).

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Bosch washer error code E17. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component Name	OEM Part Number	Manufacturer	Status
Dual Water Inlet Solenoid Valve Assembly	`00622324`	Bosch	Direct Fit OEM
Electronic Water Level Pressure Sensor	`00627460`	Bosch	Direct Fit OEM
Water Inlet Hose Filter Screen Kit	`00424981`	Bosch	Direct Fit OEM

Need Local Diagnostic Assistance?

Connect with a Certified Bosch Technician in Your Area

If multimeter testing reveals an internal short, locked motor, or fried control board, let an experienced local technician complete the repair with certified OEM replacement parts.

Call for Immediate Technician Dispatch Search Another Code

Frequently Asked Questions: Bosch E17

What causes Bosch washer error code E17?

The front-load washing machine did not reach the target water level in the tub within the programmed 6-minute fill timeout window.

Can I reset the E17 code by unplugging the washer?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E17 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Bosch E17?

Common OEM replacement components include: Dual Water Inlet Solenoid Valve Assembly (OEM #00622324), Electronic Water Level Pressure Sensor (OEM #00627460), Water Inlet Hose Filter Screen Kit (OEM #00424981).